Last updated:
At Fira Barcelona Gran Via, you can hang a truss, sign or structure over your stand only from rigging points installed by Fira’s official supplier, requested through Servifira; hanging anything directly from the hall ceiling is prohibited. Each point carries 150 kg in Halls 1, 2, 5, 7, 8.0 and 8.1 and 250 kg in Halls 3, 4 and 6, the total suspended weight may not exceed 15 kg per m² of your stand, and the hanging structure may reach a maximum height of 7 m.
Quick facts
- Rigging is an exclusive Fira de Barcelona service, delivered through its official suppliers and requested on the Servifira website. Source: Fira Barcelona Gran Via Technical Regulations, section 3.7 (PDF), checked on November 17, 2026.
- Suspended structures and floor-supported structures must be completely independent. “Mixed structures” are prohibited.
- Technical data must be submitted in International System units and in Spanish or English.
- We design, build and install stands from approx. €280/m² and reply within 24 hours.
Who installs rigging points at Fira Barcelona?
Only Fira. Section 3.7 of the Gran Via Technical Regulations states that basic anchoring points, also called rigging, are an exclusive Fira de Barcelona service offered through its official suppliers. Your stand builder or AV company can supply the truss, motors and the hanging design, but the points in the hall structure are ordered from Fira.
Points are not available everywhere. Availability depends on the hall, the points already in use and the load capacity of the roof. When a point cannot sit vertically above your hanging position, Fira’s supplier may need pre-rigging, and the regulations warn that this can add costs charged to the exhibitor.
How much weight can each rigging point carry?
The regulations give these maximum loads per authorized point for exhibitors. The weight of motors, hoists and other lifting gear counts toward the limit.
- Halls 1, 2, 5, 7, 8.0 and 8.1: 150 kg (1.47 kN) per point. Subject to a technical and structural feasibility study, high-capacity points of up to 250 kg (2.45 kN) can be installed in Halls 1, 2, 5, 7 and 8.1.
- Halls 3, 4 and 6: 250 kg (2.45 kN) per point.
- Corporate events and organizer spaces: 250 kg per point in all Gran Via halls, with high-capacity points of up to 350 kg (3.43 kN) possible in Halls 1–7 and 8.1 after a feasibility study.
Two more limits often decide the design. The total suspended weight may not exceed 15 kg per m², calculated as the total weight of the suspended elements divided by the stand surface you booked. And when manual chain hoists are used, the maximum load per point drops to 150 kg, with no more than six manual hoists lifting one truss grid.
Fira’s rigging suppliers may install load cells to check the real loads. If a point is over the limit, the exhibitor or builder has to fix it.
What are the basic rules for a hanging structure?
The main requirements in section 3.7.1:
- Exhibitor-owned trusses and materials need CE marking and must be in excellent condition.
- Trusses may be slung only with steel cables or steel-core textile slings; textile-only slings are not allowed for trusses.
- Anchoring points must be at least 1 m apart.
- Nothing may hang from the auxiliary structures installed in the venue’s ceiling, and nothing may be tied to pillars, beams, grids or installations.
- Hanging elements must keep the vertical line of the point.
- The top of the truss or aerial structure may be at most 7 m high in the exhibition area, if the hall has no lower restriction.
- Equipment installed by the official supplier, such as trusses, wires, shackles or slings, must not be altered.
What safety wires are required?
Section 3.7.2 requires safety wires for D8 electric motors and manual chain hoists. They must connect the structure to the ring and bypass the motor or hoist, stay slack once both ends are fixed, and have a diameter of at least 6 mm and no smaller than the main wires. Their capacity must cover the load plus 25% for sudden stress.
Every component hung on a truss, such as lights, speakers or signs, needs a secondary safety wire or chain and metal flanges, with steel cables of at least 4 mm. If textile slings are used, the nylon elements need a minimum tensile strength of 7 kN (700 kg) and a metal-cable connection to the truss.
Why are mixed structures prohibited?
Because a structure that is half hung and half standing shares loads in ways nobody calculated. Section 3.7.4 defines mixed structures as those that combine suspension from rigging points with floor supports, anchors or rigid connections to the floor, platforms or self-supporting structures. They are strictly prohibited.
In practice, this rules out a truss ceiling resting on stand walls while also hanging from the roof, or towers stabilized with cables to rigging points. Rigging points may not be used for stabilization, structural reinforcement, secondary safety or to supplement floor-supported structures. The two permitted configurations are a fully suspended structure, with no structural contact with the floor, and a fully self-supporting structure, with no connection to the hall roof. The same logic applies to canopies and stand ceilings: hang them completely or support them completely. See whether a stand can have a ceiling at IFEMA and Fira Barcelona.
How do you request rigging at Fira Barcelona?
Section 3.7.3 describes the request. You fill in the online form through the Fira Barcelona sales department at Servifira and send:
- A drawing, in AutoCAD 2010 if possible, showing the height, the weight each anchoring point supports and the orientation of the stand in the hall.
- The rigging request form with company details and rigging requirements.
- The point type: with or without safety wires, manual chain hoists or electric motor.
Depending on complexity, such as the number of points, the location or overlapping requests, Fira may also ask for a technical description of the materials, weight calculations for the points, material quality certificates and proof that motors and hoists have been inspected.
The general regulations do not publish a single rigging deadline for every event. Check the dates in your fair’s exhibitor area and on Servifira, and send the request as early as the stand design allows, because points are allocated case by case.
What counts as complex rigging?
Complex rigging, under section 3.7.5, covers suspended structures or elements that are not officially approved, meaning they are not industrially produced and have no technical data sheet for resistance and loads. Approved structures without lining, or unapproved suspended elements, also count as a whole. Light elements such as textiles or foam, whose fall would not put people at risk, are exempt, though you still have to justify their weight and size.
For complex rigging, the exhibitor or rigger must submit a descriptive report, a structural stability and resistance study, the weight calculations at the points and dimensioned plan and elevation drawings. A technical expert registered with a professional association must supervise the assembly. Build-up is not authorized until any deficiencies are corrected.
Fira Barcelona Gran Via rigging: key figures
| Data point | Value | Source (linked) | Date checked |
|---|---|---|---|
| Who installs rigging points | Fira de Barcelona official supplier only; request via Servifira | Gran Via Technical Regulations, 3.7 and 3.7.3 | Nov 17, 2026 |
| Max load per point, exhibitors | 150 kg in Halls 1, 2, 5, 7, 8.0, 8.1; 250 kg in Halls 3, 4, 6 | Same document, 3.7.1 | Nov 17, 2026 |
| High-capacity point (after feasibility study) | Up to 250 kg in Halls 1, 2, 5, 7, 8.1 | Same document, 3.7.1 | Nov 17, 2026 |
| Max suspended weight ratio | 15 kg per m² of booked stand surface | Same document, 3.7.1 | Nov 17, 2026 |
| Min distance between points | 1 m | Same document, 3.7.1 | Nov 17, 2026 |
| Max height of hanging structure | 7 m in the exhibition area, if the hall allows it | Same document, 3.7.1 | Nov 17, 2026 |
| Manual chain hoists | Max 150 kg per point; max 6 hoists per truss grid | Same document, 3.7.1 | Nov 17, 2026 |
| Safety wire diameter | At least 6 mm and not smaller than the main wires | Same document, 3.7.2 | Nov 17, 2026 |
| AES design and build rates (approx.) | Modular approx. €280–380/m²; custom wood approx. €450–650/m²; double-deck approx. €750–1,100/m² | AES price calculator | Nov 17, 2026 |
Quotable summary: At Fira Barcelona Gran Via, rigging points come only from Fira’s official supplier, carry 150 kg or 250 kg depending on the hall, and the total hung weight may not exceed 15 kg per m² of stand.
How is this different from IFEMA Madrid?
IFEMA publishes its own rigging regulations (PDF), checked on November 17, 2026. There, projects are due one month before assembly, IFEMA rules on each application within seven days, and the maximum load is 500 kg per point at beam connections in Halls 1–10 and 250 kg between connections. Light canvases whose rigging materials weigh under 5 kg/m² are exempt from approval. The logic is similar, but the numbers and the paperwork are not, so never reuse a Madrid rigging plan in Barcelona without checking.
Montjuïc, Fira’s city-center venue, has its own technical regulations (PDF). Use the document for the venue where your fair takes place.
Planning tips from the stand side
- Start with the weight budget. Multiply your stand surface by 15 kg to get the ceiling on all hung elements, including motors.
- Know your hall early. A 150 kg hall and a 250 kg hall can lead to different truss layouts.
- Keep it fully hung or fully standing. Decide this in the concept stage.
- Have a ground-supported alternative ready in case points are not available where you need them.
The cost of points, pre-rigging and supplier labor is set by Fira and its suppliers, not by us. Our calculator rates cover the stand: modular from approx. €280–380/m², custom wood from approx. €450–650/m² and double-deck from approx. €750–1,100/m². Try the exhibition stand cost calculator for a first range.
Plan your Fira Barcelona stand with us
We are Adam Expo Stand, founded in 2018. Adam has worked in exhibitions since 2005, and we have completed 639+ projects in 12+ countries. Based in Madrid, Spain, serving all of Europe with a focus on Spain and Portugal. We design, build and install stands and reply within 24 hours. Get your free design consultation.
Related pages: Stand ceiling rules at IFEMA and Fira Barcelona · Fira Barcelona Gran Via technical guide · Stand builder at Fira Barcelona Gran Via · Rigging approval checklist · Cost calculator.